An all-in-one remote control!
Allows the user to easily see and push buttons to control TV, VCR, DVD,
Cable, PVR, DTC Boxes and Satellite receivers. It also will control the
latest Flat Screen TV’s. The large buttons are very sensitive to touch and
have different colors for different group functions.
Size: 18"L x 10"W x 2½"H. Requires 2 AA Batteries. Weight: 2 lbs.
Operation:
1. The Universal Remote requires 2 AA batteries (Not included). Use
alkaline batteries only (e.g. Duracell or Energizer brand). Do not use
rechargeable batteries or any other type of batteries because they
supply lower voltage and the unit will not perform properly. Never mix
old and new batteries together or different brands or types together.
3. You will not be placing any batteries directly into the “One For All”
remote as this is permanently affixed to the Universal Remote.
Instead, please locate the battery compartment recessed in the back
of the Universal Remote. The battery compartment cover is secured
with a small screw. Use a Phillips head screwdriver to remove this
screw and remove the cover. Insert the 2 AA batteries into the
compartment paying careful attention to proper battery polarity.
4. Replace the compartment cover and re-secure it with the screw. Test
the unit by pressing the ON/OFF button. The red indicator light
should blink. If not, change your batteries.
• All programming will be done through the remote’s keypad on the
back of this unit. When programming make sure none of the large
buttons on the front become activated or depressed, doing so will
prevent programming of your device.
5. Turn on a desired device (e.g.VCR or DVD player) and, if applicable,
insert media (e.g., cassette or disc). On the remote control, press a
device key once (i.e., DVD/VCR, CBL/SAT, or TV).
NOTE: To program control of a VCR, PVR (or DVR), TV/VCR
Combo, or TV/VCR/DVD Player Combo press DVD/VCR once. After
programming a VCR Combo device, you will be able to control
channel selection, volume, and VCR functions.
NOTE: To program control of a DVD Player, DVD Player/VCR
Combo, or TV/DVD Player Combo, press DVD/VCR once. After
programming a DVD Combo device, you will be able to control
channel selection, volume, and DVD functions.
NOTE: To program control of a Cable Box, Cable Box/PVR (or DVR)
Combo, Satellite Receiver, or a Satellite Receiver/PVR (or DVR)
Combo, press CBL/SAT once.
6. Press and hold SET until the LED (red light) blinks twice, then
release SET. Use the Manufacturer’s Codes to locate the type of
device and brand name and then enter the first four-digit code for
your device. If performed correctly, the LED will blink twice.
7. NOTE: If the LED did not blink twice, repeat steps 6 through 7 and
enter the same code again. Aim the remote control at the device and
press POWER once. The device should turn off. If it does not, repeat
steps 6 through 7, trying each code for your brand until you find one
that works.
Volume Setting:
8. To have control of your T.V. volume while running a DVD, VCR, PVR
or CBL/SAT, you will need to lock the Volume as described on page
8 in the “One For All” instructions. Press and hold SET button until
the red light on the remote blinks twice, then release. Enter 9-9-3 and
then press T.V. key once the Red light will blink twice. Now when you
press Vol up, Vol down or Mute it will be controlled regardless of the
device you are controlling.
Troubleshooting:
If you cannot get your Universal Remote to operate any of your
devices, or it will not perform commands properly:
• Make sure that your batteries are fresh and installed correctly
(according to proper polarity). *
Rev 3/3/15
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals